6L/Min 60Bar Electric Hydro Test Pump Hydraulic Pressure

High Pressure 6L/Min 60Bar Electric Hydraulic Pressure Hydro Test Pump

6L/Min 60Bar Electric Hydraulic Pressure Hydro Test Pump

Specification of HT60A 60bar High Pressure Electric Hydraulic Test Pump

High Quality Hot Sales Water pressure testing pump Plastic pipe fitting tools for PPR PVC PE PIPES

1. Pressure: 0--60bar

2. Flow Volume: 6.0L/min

3. G.W/N.W: 17/15kgs

4. Meas.: 400*300*290mm

5. Voltage: 220v/110v

6. Power: 400w

Feature

1. For quick and exact compression testing
2. For testing of leaks in installations, especially for use in heating, compressed air, refrigeration systems, oil installations, sprinkler systems and other small bore pipe applications

Details for testing pump

INSTRUCTION FOR USE

1. Check that the gasket and the joint are well matched, and connect the water inlet pipe correctly;
2. The fire wire and ground wire must be correctly connected before use, and must not be wrongly connected! The power cord should be connected to a socket with leakage protection.
3. Loosen the pressure regulating knob first, do not start the motor with load, so as not to damage the motor
4. Check the filter regularly to avoid clogging
5. If the water pump cannot absorb water, please add a certain amount of water from the water inlet pipe to the water pump.
6. Prevent air from entering the water pump.
7. After the pressure test is over, loosen the pressure adjustment knob, add a little 20# oil, and keep it loose. At the same time, turn on the power and add oil at the water inlet to run for half a minute.
8. It is strictly forbidden to start the machine without water, otherwise the sealing ring and piston ring will be easily damaged.
9. The water source should not have impurities, otherwise the seal will be easily stuck, which will cause the phenomenon of no water absorption.
10. Water leakage at the lower part of the pump body means that the sealing ring is damaged, and the sealing ring must be replaced.
11. Please use the pressure regulating button correctly, do not turn the pressure regulating knob to the end, otherwise the high pressure will cause high pressure damage to the meter, etc.

Note: Be sure to loosen the red pressure regulating valve before turning it on! so as not to explode the pressure gauge

We also has other size and plug in store, pls check as your need

The new technical solution of the electric pressure test pump has the following advantages:

1. The electric pressure test pump provided by the new electric pressure test pump has the advantages of small size and easy operation, and the liquid is pressurized into the external pipeline through the power pump to achieve the For the purpose of pressurizing the external pipeline, compared with the traditional manual pressure test pump, the new electric pressure test pump not only saves manpower but also improves the efficiency. By using a diaphragm pump, it can provide sufficient power under the premise of ensuring a small volume.
2. When it is necessary to pressurize the pipeline to be measured, first make sure that the valve is closed so that the water inlet pipeline and the water outlet pipeline are in a disconnected state, then connect the water inlet pipeline to the liquid source, and connect the water outlet pipeline to the pipeline to be measured. Connected, the user can control the power pump to work through the control switch, and the user can grasp the pressure value of the water outlet pipeline in real time through the pressure display at the mechanical pressure gauge. When the water outlet pipeline reaches the expected pressure, it means the pipeline to be tested at this time. When the expected pressure is reached, the power pump is stopped by controlling the control switch, and the pressurization of the pipeline to be tested is completed at this time. After the test is completed, the control valve is opened, so that the water inlet pipeline and the water outlet pipeline are connected through the connecting pipeline, and the water body with higher pressure at the water outlet pipeline flows to the water inlet pipeline, so as to realize the pressure relief of the water outlet pipeline to the water inlet pipeline.

Our advantage:

1. Quick, efficient and professional response within 24 hours,
2.15 years manufacturing experience in plastic pipe &fitting field.
3. Reasonable price and shorter production cycle.
4. Technical support and solution by chief engineer.
5. Strict quality control system and team
6. Full range of pipe& fitting products for choice
7. OEM or ODM services both available for our company
8. Accept sample order before mass order
9. On-time delivery, and 24 hour after-sales service